Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Other

$12.99
COMPATIBLE WITH THE FOLLOWING ONEUP GUIDES - CHAIN GUIDE - ISCG05 - V2 - BASH GUIDE - ISCG05 - V2 - E-BIKE - STEPS/EP8 - Kit includes 1 two piece top guide
$14.99
V2 dropper remote clamp for 22.2mm handlebar.
$14.99
Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with Shimano I-Spec EV (M9100, M8100, M7100) brake mounts. - Does not contain remote body.
$14.99
Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with Shimano I-SPEC-II brakes - Not Compatible with Shimano I-SPEC-A or B - Does not contain remote body.
$14.99
Replacement dropper post remote clamp. Can be used to convert existing clamp on the OneUp Dropper Remote. - Compatible with SRAM MatchMakerX (MMX) or Shimano I-Spec EV (M9100) brake mounts. - Does not contain remote body.
$14.99
Don’t get stuck between dropper sizes. The unique OneUp travel adjust shims allow you to custom tune your OneUp Components Dropper post by lowering the travel and extended length of your post by either 10mm or 20mm. A 180mm travel post can be reduced in travel to either 170mm or 160mm with this shim kit. Drop tuning can be done on-bike, tool free and without removing the saddle or touching a shock pump. Lowering the post travel also increases bushing overlap and alignment pin length, which is great for heavier riders. - 210mm Dropper Post - adjustable down to 190mm - 180mm Dropper Post - adjustable down to 160mm - 150mm Dropper Post - adjustable down to 130mm - 120mm Dropper Post - adjustable down to 100mm
$18.99
This kit includes all the parts required to rebuild your V2 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V2 Dropper Post ONLY.
$18.99
Set of six oversized pins. All dropper posts require key way clearance. With so many different frames, clamps and ride heights it's not possible to ship play-free without running the risk of binding. The kit is meant to remove additional play that might develop over time or, for the more mechanically inclined, to tune the play out for a specific bike. Start with the 3 pins marked with 2 lines. If play still exists move to the 3 pins marked with 4 lines.
$18.99
- Replacement bolts for Switch carriers
$27.99
SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with both Shimano Hypergilde+ 12 speed chains and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - 3 Offsets - Regular, Boost and Super Boost - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 69g (30T Boost Cinch Oval) - Chainline: Regular (49mm), Boost (52mm), Super Boost (56.5mm) - Compatibility: Race Face Cinch cranks; 9, 10, 11 and 12 Speed Chains
$27.99
SWITCH. A QUICK-CHANGE DIRECT MOUNT CHAINRING SYSTEM FROM ONEUP COMPONENTS. Switch was developed to reduce the cost of replacement chainrings, increase compatibility with new offsets and to make the process of changing your chainring much faster and simpler. - Cheaper Replacement Cost - Replacement rings are a fraction of the cost of a complete direct mount chainring - Quick Change - Replace your ring in less than an minute, using only a 4mm hex key. Tailor your gearing to the terrain that you're riding - Enduro World Series Champion Winning Narrow Wide tooth profile keeps your chain in place on the roughest terrain - 4 Ring Sizes (28, 30, 32, 34T) - 2 Profiles - both Round and Oval - 12 speed ring designed to work with both Shimano Hypergilde+ 12 speed chains and SRAM Eagle 12 speed chains. - Get ultimate traction with Oval rings by smoothing out the torque you deliver to your rear tire - 3 Offsets - Regular, Boost and Super Boost - Quick Change Rings can be replaced in less than a minute with only a 4mm allen key, without removing your crank. Simply loosen the bolts 2 turns, unlock the ring by rotating it by 20 degrees and pull it over and off your crank. Reverse these steps to install your new ring. If you plan to ride a trail that you know is steeper than your local trails, you can switch to a smaller ring in the parking lot, in less time than it takes your friend to put on his riding shoes! SPECS - Material: 7075-T6 - Weight: 66g (30T Boost Oval) Chainline: - 6mm offset - 49mm GXP/BB30 Long Spindle - 3mm offset - 52mm (Boost) GXP/BB30 Long Spindle - 0mm/SB - 49mm BB30 Short spindle, 56mm GXP/BB30 Long Spindle Compatibility: SRAM DM cranks; 9, 10, 11 and 12 Speed Chains
$28.99
The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8" aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. KIT INCLUDES - EDC TOP CAP - EDC steerer plug - 2x 1mm, 3mm, & 5mm Headset Spacers
$49.99
If you're not looking for chain retention or your bike has an integrated chain guide, you can still add some bash protection with the OneUp ISCG05 Underbash. The Underbash includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. Designed for frames with 2 ISCG05 tabs only (Evil, Rocky Mountain, etc). If your bike has three ISCG05 tabs, check with the frame manufacturer to ensure the lower tabs are strong enough for a bash application. Failure to do so could result in frame damage. FEATURES - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) SPECS - Weight: 68g 32-34T - Capacity: 28-36T - Chainline: 2.5mm adjustment - Mount: ISCG05 2-Bolt ONLY - Color: Black - Material: 7075 aluminum, glass reinforced thermoplastic
$59.99
Eliminate dropped chains forever with the new OneUp Components Guide. As the trend for lower and slacker bikes continues, 'Little bikes' are getting more and more capable everyday. Revised for 2019 the OneUp Guide uses simple, one tool installation and adjustment as well as an all new tool less flip At only 40g the OneUp Chain Guide weighs less than a sip of water. WHY DO I NEED A GUIDE AND A NARROW WIDE CHAINRING? NW rings are awesome, but they're not perfect and every once in a while you can drop a chain while riding. On a social ride this means getting dropped by your friends. But when racing an Enduro a dropped chain can cost you the podium, which is why almost every EWS pro runs both a chainguide and narrow wide chainring. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment (4mm hex) - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 40g - Capacity: 26-38T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic
$69.99
Eliminate dropped chains forever and add a touch of colour to your e-bike with the new OneUp Components STEPS Chain Guide. Available in 7 colours. The OneUp STEPS Chain Guide is lightweight and incredibly easy to install and use. The top guide has a tool-free flip feature that allows easy access to your chain for cleaning and maintenance. Top guide pieces are available in 6 bright colours to perfectly match your OneUp Composite Pedals, Grips and EDC Lite. Compatible with 32T to 38T chainrings. Weighs just 45g. FEATURES - Shimano STEPS E7000, E8000 and EP8 compatible - Includes black top guide piece. 6 other colours sold separately - Tool-less upper guide flip - Install without removing your cranks - Mounts directly to motor - Single tool install and adjustment (4mm hex) - Black Stainless-Steel hardware - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 45g - Capacity: 32-38T - Chainline: 5mm adjustment - Mount: Shimano STEPS/EP8 - Colour: Black top guide piece included. Blue, Green, Orange, Purple, Red, Turquoise sold separately. - Material: Back Plate - 7075 aluminum, Top Guide - glass reinforced thermoplastic
$94.99
Eliminate dropped chains forever with the new OneUp Components Bash Guide. As the trend for lower and slacker bikes continues, chainring protection is becoming even more important. Revised for 2019 the OneUp Bash Guide uses simple, one tool installation and adjustment as well as an all new tool less flip The OneUp Bash Guide was developed with input from top EWS World racers and can be seen all over this years circuit. Reinforced Nylon bash guards and a back plate cut from 8mm thick 7075-T6 aluminum, ensure that the OneUp Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you may forget it’s even there. NOT JUST FOR ENDURO RACERS. The OneUp Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers and Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention. The OneUp Bash Guide includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 90g 28-30T, 105g 32-34T, 110g 36T - Capacity: 28-36T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic
Page 1 of 1